(PDF) DCA-Networking DEA-5TT2 Exam and Certification Test Engine
Use DEA-5TT2 Exam Dumps (2023 PDF Dumps) To Have Reliable DEA-5TT2 Test Engine
NEW QUESTION # 25
Which flags are used in the TCP header to initiate and end TCP connections or sessions?
- A. Initiate = Finish (FIN) End = Synchronize (SYN)
- B. Initiate = Acknowledge (ACK) End = Synchronize (SYN)
- C. Initiate = Acknowledge (ACK) End = Finish (FIN)
- D. Initiate = Synchronize (SYN) End = Finish (FIN)
Answer: D
NEW QUESTION # 26
On which OSI layers do standard ACL filters operate?
- A. 4 and 7
- B. 2 and 3
- C. 2 and 7
- D. 3 and 4
Answer: D
NEW QUESTION # 27
What is the aggregated lanes' maximum speed rating for a QSFP28 transceiver?
- A. 4 Gbps
- B. 112 Gbps
- C. 128 Gbps
- D. 40 Gbps
Answer: B
NEW QUESTION # 28
A Dell EMC Networking N-Series switch is configured on a port channel with LACP using the interfaces Te1/0/1 and Te1/0/2. How is the egress traffic distributed among the interfaces?
- A. Load balanced using a hash function
- B. Load balanced per packet using round robin
- C. Traffic overflow will be sent to the second interface
- D. Interfaces will be used in active/passive
Answer: A
NEW QUESTION # 29
Which component translates data, signaling, and protocols to facilitate the data flow between the end device and the network?
- A. Transceiver
- B. NIC
- C. Switch
- D. Port
Answer: A
NEW QUESTION # 30
On which Dell EMC Networking switches can Multi-Chassis Link Aggregation (MLAG) be configured?
- A. S-Series
- B. C9000 Series
- C. N-Series
- D. Z-Series
Answer: C
NEW QUESTION # 31
Which formula is used for calculating OSPF interface costs?
- A. Reference bandwidth + interface bandwidth
- B. Interface bandwidth / reference bandwidth
- C. Reference bandwidth / interface bandwidth
- D. Reference bandwidth - interface bandwidth
Answer: B
NEW QUESTION # 32
Which criteria is used to define an extended MAC ACL filter?
- A. Destination MAC address and Ethernet frame type
- B. Ethernet frame type and frame size
- C. Source and destination MAC addresses
- D. Destination TCP port number and source MAC address
Answer: C
NEW QUESTION # 33
In IPv4, what is the proper conversion from binary to decimal for the number 11010010?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 34
A network administrator is troubleshooting an OSPF routing issue. There are two paths to a destination network from one switch. In addition, one path is comprised of four 1 Gb links. The other path is comprised of two 1 Gb and two 100 Mb links. The administrator ran several trace routes and notices that the packets are swapping back and forth between the two paths.
Which corrective action must be taken on the switch infrastructure to correct this issue?
- A. Change the reference speed used by OSPF in cost calculations on all switches within the path.
- B. Switch all routing protocols to RIPv2.
- C. Break the paths into multiple OSPF areas.
- D. Manually specify the OSPF Router ID on each switch within the path.
Answer: A
NEW QUESTION # 35
Router A is directly connected to Router B over an Ethernet link. The local interface address for the Router A Fo0/48 interface is 144.254.32.2/24. Which routing table entry is visible on Router A?
- A. 144.254.0.0/16
- B. 144.254.32.0/24
- C. 144.254.0.0/24
- D. 144.254.32.2/24
Answer: B
NEW QUESTION # 36
Which IPv6 scope is used for private addressing on a local network?
- A. Area wide
- B. Global
- C. APIPA
- D. Unique local
Answer: D
NEW QUESTION # 37
Which IPv4 address is in the same network as the IP address 182.15.24.40/23 and assignable to a host device?
- A. 182.15.23.224
- B. 182.15.26.10
- C. 182.15.25.255
- D. 182.15.25.0
Answer: D
NEW QUESTION # 38
What are the Protocol Data Units (PDUs) called at the Transport layer?
- A. Segment
- B. Packets
- C. Frame
- D. Data Payload
Answer: A
NEW QUESTION # 39
What accurately describes the comparison between stacking and VLT?
- A. Both VLT and stacking allow devices to use different versions of firmware provided that the switch family/ series is the same.
- B. Stacked switches share a common control plane while VLT peers maintain their own control plane.
- C. VLT allows for more physical devices to appear as one virtual device than stacking does.
- D. Stacked switches and VLT peers allow "single pane of glass" management by maintaining a single control plane.
Answer: B
NEW QUESTION # 40
What is the default route preference value for a Border Gateway Protocol (BGP) internal route?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 41
A network administrator has a Dell EMC switch that has been configured with several VLANs. Each VLAN switch virtual interface (SVI) has an IP address assigned to it with each of them on different subnets. In addition, routing has been enabled on the switch.
Which action occurs when the switch receives a packet on one of its SVIs but the destination IP address of the packet does not match the IP address of that SVI?
- A. Switch replies back to the source with an ICMP Reject packet.
- B. Switch drops the packet.
- C. Switch duplicates the packet and sends it to all interfaces.
- D. Switch checks its routing table and forwards the packet accordingly.
Answer: D
NEW QUESTION # 42
What is the default OSPF "hello interval"?
- A. 30 seconds
- B. 15 seconds
- C. 5 seconds
- D. 10 seconds
Answer: D
NEW QUESTION # 43
Which option is used to configure Network Address Translation (NAT) to provide one-to-one mapping between local and global addresses?
- A. Inside source static
- B. Overload
- C. PAT
- D. Outside source static
Answer: A
NEW QUESTION # 44
The IEEE separates the Data Link and Physical ISO layers into four sub-layers. Based on the exhibit, what is the correct order of these sub-layers; from lowest to highest?
Answer:
Explanation:
NEW QUESTION # 45
Which Dell EMC Networking M-Series 10 GbE switch model supports a VLT?
- A. MXL
- B. M6220
- C. M8024-K
- D. M6348
Answer: A
NEW QUESTION # 46
Which port type should be used for only VLAN-unaware devices?
- A. General port
- B. Trunk port
- C. Access port
- D. Hybrid port
Answer: D
NEW QUESTION # 47
......
EMC DEA-5TT2 certification is a valuable credential for networking professionals who want to advance their careers. Associate - Networking Exam certification demonstrates that the candidate has the knowledge and skills to manage complex networking infrastructure and to troubleshoot and resolve issues related to networking and storage. Associate - Networking Exam certification is recognized by many companies and organizations, and it can help networking professionals to stand out in a competitive job market.
DEA-5TT2 Dumps Full Questions with Free PDF Questions to Pass: https://www.lead2passexam.com/EMC/valid-DEA-5TT2-exam-dumps.html
DEA-5TT2 PDF Recently Updated Questions Dumps to Improve Exam Score: https://drive.google.com/open?id=108dbISNtFJsTglIP6VU60F1oZmiYR6iO