Easily To Pass New NS0-521 Verified & Correct Answers [Jul 13, 2025
Free NS0-521 Exam Files Downloaded Instantly
NEW QUESTION # 37
A customer needs to verify if jumbo frames have been configured correctly for an ISCSI workload. Which command should be used?
- A. pig -lif <-F> -vserver <SVM> -destination <IP> -disallow-fragmentation true -packet-size 9000
- B. pig "lif <LIF> -vserver <svm> -destination <ip> -disallow-fragmentation true -packet-size 8900
- C. pig -lif <1IF> -vserver <SVM> -destination <IP> -disallow-fragmentation false -packet-size 1500
- D. ping -lif <LIF> -vserver <SVM> -destination <IP> -disallow-fragmentation true -packet-size 1500
Answer: A
Explanation:
To verify if jumbo frames have been configured correctly for an iSCSI workload, the command ping -lif
<LIF> -vserver <SVM> -destination <IP> -disallow-fragmentation true -packet-size 9000 should be used. This command tests the network path with the jumbo frame size (9000 bytes) and ensures that the packets are not fragmented, confirming that jumbo frames are supported end-to-end.
For more details, you can check:
* NetApp Documentation on iSCSI Configuration
* NetApp Community Discussions on Jumbo Frames
NEW QUESTION # 38
A customer has a 10GB volume with an 8GB LUN that is using 7GB. The snapshot policy is hourly and retains 48 snapshots. After a ransomware attack that encrypts all files on the LUN, the customer notices that all snapshots are gone.
What could cause this behavior?
- A. Volume thinly provisioned
- B. Aggregate overcommitted
- C. Snapshot autodelete
- D. Autonomous Ransomware Protection
Answer: C
Explanation:
The likely cause for the disappearance of all snapshots after a ransomware attack that encrypted all files on the LUN is the Snapshot autodelete feature. When the volume becomes full due to the encryption, the autodelete feature removes older snapshots to free up space, preventing the volume from running out of space and ensuring write operations can continue.
For more information, see:
* NetApp Documentation on Snapshot Autodelete
* NetApp Community Discussion on Snapshot Deletion
NEW QUESTION # 39
What is the minimum number of rack units that are required on each site for a NetApp AFF All San Array (ASA) A800 MetroCluster IP configuration with 72 disks per site and Cisco N9K-C9336C-FX2 backend switches?
- A. 4 RU
- B. 12 RU
- C. 16 RU
- D. 8 RU
Answer: C
Explanation:
For a NetApp AFF All SAN Array (ASA) A800 MetroCluster IP configuration with 72 disks per site and Cisco N9K-C9336C-FX2 backend switches, the minimum number of rack units required on each site is 16 RU. This includes space for the controllers, disk shelves, and the necessary network switches. This configuration ensures that all components are properly accommodated and operational within the specified rack space.
For detailed information on the rack unit requirements and MetroCluster IP configurations, refer to:
* NetApp Documentation on MetroCluster IP
* MetroCluster IP Solution Architecture
NEW QUESTION # 40
What Is a recommended setting for using the NetApp ONTAP LUN fractional reserve?
- A. Volume Snapshot copy automatic deletion is disabled.
- B. Space allocation is set to enable.
- C. LUN space reservation is disabled.
- D. Space guarantee is set to volume.
Answer: D
Explanation:
The recommended setting for using the NetApp ONTAP LUN fractional reserve is to set the space guarantee to "volume". This setting ensures that the required space for overwrites in the volume is reserved, preventing potential write failures when snapshot copies are created. This setup helps in maintaining the performance and reliability of the storage system by ensuring there is always enough space allocated for the LUN.
For further details, you can refer to:
* NetApp Community Discussion on Fractional Reserve
* NetApp Documentation on Space Management
NEW QUESTION # 41
A storage engineer in SAN environment needs to Identify FC ports using the company-wide naming policy.
Which command will accomplish this task?
- A. TCP portname set
- B. network interface modify
- C. vserver fcp wwpn-alias set
- D. ucadmin modify
Answer: C
Explanation:
The vserver fcp wwpn-alias set command is used to set or modify the World Wide Port Name (WWPN) aliases for Fibre Channel (FC) ports in a NetApp ONTAP environment. This command allows you to apply a company-wide naming policy to FC ports, ensuring consistent and easily identifiable naming conventions across your storage infrastructure.
For further details, you can refer to:
* NetApp Documentation on FC Management
* NetApp Community Discussion on WWPN Aliases
NEW QUESTION # 42
A customer Is deploying a new 8-node NetApp ONTAP cluster for their SAN workloads using FCP, NVMe/FC, and NVMe/TCP.
In this scenario, which statement is true?
- A. NVMe/TCP can only run at 32Gbps or faster.
- B. NVMe/FC and FCP require different FC ports.
- C. NVMe/TCP supports a maximum of two LIFs per node.
- D. NVMe/FC and NVMe/TCP must be configured in separate SVMs.
Answer: B
Explanation:
In a NetApp ONTAP cluster using FCP, NVMe/FC, and NVMe/TCP, it is important to understand that NVMe/FC and FCP require different FC ports. This separation is necessary because the protocols, while both running over Fibre Channel, have different configurations and operational characteristics.
For more information, refer to:
* NetApp Documentation on NVMe Configuration
* NetApp Best Practices for SAN
NEW QUESTION # 43
An administrator needs to ensure that Snapshot copies of database files across multiple FCP LUNs are taken at the same point in time.
Which two configurations enable the administrator to achieve this? (Choose two.)
- A. Create each LUN within the same FlexGroup volume.
- B. Create a consistency group that uses FlexVol volumes.
- C. Create each LUN within the same FlexVol volume.
- D. Create a consistency group that uses FlexGroup volumes.
Answer: A,B
Explanation:
To ensure that Snapshot copies of database files across multiple FCP LUNs are taken at the same point in time, the following configurations can be used:
* Create a consistency group that uses FlexVol volumes: This setup ensures that snapshots of all volumes in the consistency group are taken simultaneously.
* Create each LUN within the same FlexGroup volume: This configuration allows for a unified snapshot across multiple LUNs within the FlexGroup, ensuring data consistency.
For more details, see:
* NetApp Documentation on Consistency Groups
* NetApp FlexGroup Overview
NEW QUESTION # 44
A storage administrator recently implemented ISCSI SAN in a customer environment. Which two actions should be done to ensure the best performance? (Choose two.)
- A. Configure Jumbo frames In the entire data path.
- B. Connect host and storage ports to the same switches.
- C. Decrease the default queue depth on the host to eight.
- D. Zone the host by using the host WWPNs.
Answer: A,B
Explanation:
To ensure the best performance in an iSCSI SAN implementation:
* Connect host and storage ports to the same switches: This minimizes latency and maximizes the efficiency of data paths by ensuring direct connections within the same network segment.
* Configure Jumbo frames in the entire data path: Setting a larger Maximum Transmission Unit (MTU) size reduces the overhead for processing each packet, thus improving overall network performance. Ensuring Jumbo frames are configured end-to-end in the data path is crucial for optimal
* performance.
For further details, check:
* NetApp Best Practices for iSCSI
* NetApp Community Discussion on iSCSI Performance
NEW QUESTION # 45
When using tagged VLANs on Cisco Nexus switches for NVMe over TCP, which two changes must be made to enable jumbo frames? (Choose two.)
- A. Modify the Cisco Nexus switches to use an MTU of 9216.
- B. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216.
- C. Modify the Cisco Nexus switches to use an MTU of 9000.
- D. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9000.
Answer: A,B
Explanation:
For enabling jumbo frames on Cisco Nexus switches for NVMe over TCP with tagged VLANs, the following changes are required:
* Modify the Cisco Nexus switches to use an MTU of 9216: Setting the MTU to 9216 ensures that the network can handle jumbo frames, reducing the number of packets needed for large data transfers and thus improving performance.
* Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216:
This setting must match the network configuration to ensure end-to-end support for jumbo frames, which is essential for optimizing performance in NVMe over TCP environments.
For additional information, refer to:
* NetApp Documentation on NVMe over TCP
* Cisco Documentation on Jumbo Frames
NEW QUESTION # 46
What are two benefits of implementing VLANs for NVMe/TCP configurations? (Choose two.)
- A. Increased resiliency
- B. Reduced number of IPspaces
- C. Reduced number of broadcast domains
- D. Increased security
Answer: A,D
Explanation:
Implementing VLANs for NVMe/TCP configurations provides several benefits, two of which are increased resiliency and increased security:
* Increased Resiliency: VLANs help segment the network traffic, reducing the risk of a single point of failure. By isolating NVMe/TCP traffic into specific VLANs, network issues can be contained within a VLAN, preventing them from affecting other parts of the network. This isolation ensures that disruptions are minimized and network resiliency is enhanced.
* Increased Security: VLANs provide an added layer of security by segregating traffic. This segregation ensures that NVMe/TCP traffic is isolated from other types of traffic, reducing the risk of unauthorized access or data breaches. VLANs help in enforcing stricter access controls and monitoring, thereby increasing the overall security of the network.
For more information on the benefits of VLANs in NVMe/TCP configurations, you can refer to NetApp's technical resources:
* Implementing and Configuring Modern SANs with NVMe-oF (NetApp).
* SAN Configuration Best Practices (NetApp Community).
NEW QUESTION # 47
A customer wants to configure an NVMe protocol-based NetApp ONTAP based storage system in a SAN environment.
What is used to configure the list of hosts?
- A. igroup
- B. Subsystem
- C. LUN
- D. Namespace
Answer: B
Explanation:
When configuring an NVMe protocol-based NetApp ONTAP storage system in a SAN environment, a subsystem is used to configure the list of hosts. A subsystem in the NVMe context is an entity that groups NVMe namespaces (storage units) and presents them to the connected hosts. The hosts access these namespaces through the subsystem, allowing for efficient management and configuration of NVMe resources.
This configuration ensures that the appropriate hosts have access to the necessary namespaces for storage operations. This approach is critical in NVMe SAN environments to maintain high performance and manageability.
For further details, refer to:
* NetApp Community - How to Configure NVMe/TCP (NetApp Community).
* NetApp Documentation - NVMe Overview (NetApp).
NEW QUESTION # 48
A site survey has been conducted for an installation of a switchless HA pair with two NetApp DS224C shelves in the customer's already populated rack.
Which of the following two need to be verified to ensure a successful deployment? (Choose two.)
- A. Rack units
- B. Crash cart location
- C. Power connections
- D. Cluster switch location
Answer: A,C
Explanation:
For a successful deployment of a switchless HA pair with two NetApp DS224C shelves in an already populated rack, it is crucial to verify:
* Rack units: Ensure that there are enough rack units available to accommodate the new shelves and any associated equipment. Proper planning of space in the rack is essential for a neat and functional setup.
* Power connections: Verify that there are sufficient and appropriately rated power connections available. Ensuring proper power distribution and redundancy is critical for the reliability and uptime of the storage system.
For more details, refer to:
* NetApp Documentation on Rack Installation
* NetApp Community Discussion on Power Connections
NEW QUESTION # 49
A customer opens a support case for performance issues with an FC Oracle database after migrating from a NetApp AFF system to a NetApp All SAN Array (ASA) platform. Further investigation shows that the number of paths exceeds the recommendation for SAN deployment.
What are two ways to address this problem? (Choose two.)
- A. Have the database team change their backup and recovery schedules for the database.
- B. Reconfigure the fabric switch zoning.
- C. Reconfigure the ALUA settings.
- D. Use Selective LUN Mapping.
Answer: B,D
Explanation:
When the number of paths exceeds the recommended configuration for SAN deployment, it can cause performance issues. To address this problem, you can:
* Use Selective LUN Mapping (SLM): SLM allows you to control which LIFs (Logical Interfaces) are used to access specific LUNs, thus reducing the number of paths and potentially improving performance by aligning with best practice configurations.
* Reconfigure the fabric switch zoning: Adjusting the zoning on the fabric switches can help manage and optimize the number of paths, ensuring that there are not too many paths that could lead to inefficient I/O operations and performance degradation.
For more details, refer to:
* NetApp SAN Host Configuration
* NetApp Best Practices for SAN
NEW QUESTION # 50
A customer has created an SVM for their SAN workloads. They now want to configure the SVM to use NVMe/FC. Which two steps are needed to accomplish this task? (Choose two.)
- A. Create an NVMe/FC LIF.
- B. Add the FC protocol.
- C. Create the FC service.
- D. Create the NVMe service.
Answer: A,B
Explanation:
To configure an SVM to use NVMe/FC, the following steps are necessary:
* Add the FC protocol: This step involves enabling the Fibre Channel protocol on the SVM, which is required to support NVMe over Fibre Channel.
* Create an NVMe/FC LIF: Logical Interfaces (LIFs) must be created to handle NVMe traffic over the Fibre Channel network. These LIFs enable the NVMe namespace access to the host systems.
These steps ensure that the SVM is correctly set up to use NVMe/FC, allowing for efficient and high-performance access to NVMe storage.
For more information, refer to:
* NetApp NVMe/FC Configuration
NEW QUESTION # 51
An administrator configured an SVM with LUNs with two WWPNs per node. The administrator accidentally created a WWPN on node1that needs to move to node2. The SAN hosts use ALUA.
Based on this requirement, what must be taken offline to correct the situation?
- A. LIF
- B. SVM
- C. LUN
- D. Volume
Answer: A
Explanation:
To move a WWPN from node1 to node2 in a NetApp ONTAP SAN environment where ALUA is used, you must take the Logical Interface (LIF) offline. Modifying LIFs involves changing their assignment between nodes, which requires them to be temporarily offline. This ensures that the path states are correctly updated without causing disruption to the SAN hosts.
For more details, see:
* NetApp Community on Moving LIFs
* NetApp Documentation on SAN LIFs
NEW QUESTION # 52
A customer has a two-node NetApp AFF ASA cluster in an environment with a Cisco Fibre Channel SAN and Cisco UCS Servers. The customer wants to upgrade the UCS Server BIOS and the Cisco NX-OS system running on the switches.
Which NetApp resource should be consulted to check compatibility with the new versions?
- A. BlueXP digital advisor
- B. Hardware Universe
- C. Interoperability Matrix Tool (IMT)
- D. Active IQ Config Advisor
Answer: C
Explanation:
When planning to upgrade the UCS Server BIOS and Cisco NX-OS system running on the switches in a NetApp AFF ASA cluster environment, theInteroperability Matrix Tool (IMT)is the recommended resource to check compatibility with the new versions. The IMT provides detailed compatibility information for various hardware and software components, ensuring that the planned upgrades will not cause any interoperability issues.
For further details, refer to:
* NetApp Interoperability Matrix Tool
NEW QUESTION # 53
An administrator creates a new volume and a LUN for an SAN-connected application that uses snapshots. The application has fast-growing data that is constantly being populated and deleted afterwards.
Which option can be set to manage the space automatically?
- A. Unmap the LUN.
- B. Disable volume snapshot autodelete.
- C. Enable automatic resizing on the volume.
- D. Enable space reservation on the LUN.
Answer: C
Explanation:
To manage space automatically for a volume containing a LUN with fast-growing data, enabling automatic resizing on the volume is recommended. This feature allows the volume to grow dynamically as needed, accommodating the fluctuating data size without manual intervention. This helps in managing storage efficiently and ensures that the application has the required space.
For further details, refer to:
* NetApp Documentation on Volume Management
* NetApp Community Discussion on Automatic Resizing
NEW QUESTION # 54
An administrator finishes an installation of a new NetApp ASA system at the customer site and creates a new LUN. The customer wants to restrict the access of the LUN to specific UFs.
Where would the administrator configure this?
- A. igroup
- B. Portset
- C. Zoning
- D. Selective LUN Map
Answer: A
Explanation:
To restrict access to a newly created LUN to specific hosts, the administrator should configure theigroup (initiator group). An igroup is used to control which initiators (hosts) are allowed to access specific LUNs.
This ensures that only authorized hosts can access the storage, enhancing security and access control.
For more details, refer to:
* NetApp Documentation on iGroups (NetApp).
NEW QUESTION # 55
A four-node NetApp ONTAP SAN cluster has been deployed. After installation, the engineer wants to verify cabling.
Which NetApp tool should the engineer use?
- A. Active IQ Config Advisor
- B. Hardware Universe
- C. Interoperability Matrix Tool
- D. NetApp Host Utilities package
Answer: A
Explanation:
To verify the cabling of a four-node NetApp ONTAP SAN cluster after installation, the recommended tool is Active IQ Config Advisor. This tool provides detailed checks for proper configuration, including cabling verification, and helps ensure that best practices are followed for optimal performance and reliability.
For further details, see:
* NetApp Active IQ Config Advisor
NEW QUESTION # 56
A customer wants to Implement a NetApp AFF system at a small remote site that has two ESXi servers that require SAN storage from the NetApp ONTAP based storage system. The servers will be directly connected, because the customer does not want to deploy any switches.
Which protocol should the customer use?
- A. iSCSI
- B. FCoE
- C. FCP
- D. NFS
Answer: A
Explanation:
For a small remote site with two ESXi servers requiring SAN storage and no switches, the recommended protocol isiSCSI. iSCSI allows for direct connectivity between the servers and the NetApp ONTAP storage system using standard Ethernet infrastructure, which is suitable for environments without Fibre Channel switches.
For more information, see:
* NetApp iSCSI Configuration Guide
NEW QUESTION # 57
During maintenance of A NetApp AFF ONTAP cluster, which two steps are needed to move the SAN UFs to new nodes that are members of a portset? (Choose two.)
- A. Disable the zoning of the LIF WWPN.
- B. Remove the LIF from the portset.
- C. Disable the SLM feature for the node that hosts the LIF.
- D. Take the SAN LIF offline.
Answer: B,D
Explanation:
To move SAN LIFs to new nodes that are members of a portset during maintenance of a NetApp AFF ONTAP cluster, you should take the following steps:
* Remove the LIF from the portset: This ensures that the LIF is no longer associated with the current node, preparing it for the move to the new node.
* Take the SAN LIF offline: This step is necessary to make configuration changes without causing disruption to the SAN hosts. Once offline, the LIF can be moved to the new node and reconfigured as needed.
These actions help maintain the integrity and performance of the SAN environment during the migration of LIFs.
For more details, see:
* NetApp Documentation on Moving SAN LIFs
* NetApp Community on Moving LIFs
NEW QUESTION # 58
A customer has a two-node NetApp ONTAP cluster that Is hosting FC LUNs for 64 SAN hosts. An administrator is tasked to add 40 more hosts to the environment.
What two actions would the administrator need to take to avoid potential performance problems with the environment? (Choose two.)
- A. Configure additional SAN LIFs.
- B. Configure additional FC target ports.
- C. Configure additional FC ports on existing hosts.
- D. Configure a higher queue depth on the target ports.
Answer: A,B
Explanation:
When adding 40 more hosts to a two-node NetApp ONTAP cluster that is already hosting 64 SAN hosts, the following actions are necessary to avoid potential performance problems:
* Configure additional FC target ports: Increasing the number of Fibre Channel (FC) target ports on the storage nodes will help distribute the I/O load more evenly, reducing the risk of bottlenecks.
* Configure additional SAN LIFs: Adding more SAN Logical Interfaces (LIFs) will ensure that the increased number of hosts can connect efficiently, improving load balancing and path management.
These actions help maintain optimal performance and prevent congestion in the SAN environment.
For more detailed guidance, refer to:
* NetApp SAN Host Configuration Overview
* NetApp Best Practices for SAN (NetApp) (NetApp)
NEW QUESTION # 59
An administrator upgraded their NetApp ONTAP software from release 9.10.1 to 9.13.1 on a NetApp All SAN Array (ASA) cluster and is creating a new iSCSI SVM.
Which automatic feature can be used with iSCSI?
- A. CHAP authentication
- B. LUN mapping
- C. LIF failover
- D. igroup creation
Answer: C
Explanation:
In NetApp ONTAP 9.13.1, one of the automatic features that can be used with iSCSI isLIF failover. This feature ensures that in the event of a network failure or a node issue, the Logical Interface (LIF) will automatically fail over to another available port, maintaining connectivity and minimizing disruption to iSCSI traffic.
For more information, refer to:
* NetApp ONTAP 9.13.1 Features
NEW QUESTION # 60
Which NetApp feature presents LUNs only within the HA pair?
- A. Consistency group
- B. igroup
- C. Subsystem
- D. Selective LUN Mapping
Answer: D
Explanation:
Selective LUN Mapping (SLM) is the feature that presents LUNs only within the HA pair. SLM allows administrators to control which LUNs are visible to which hosts, ensuring that LUNs are only accessible through the designated HA pair, thus improving security and manageability.
For more information, see:
* NetApp Documentation on Selective LUN Mapping
* NetApp Community on LUN Mapping
NEW QUESTION # 61
......
100% Pass Guaranteed Free NS0-521 Exam Dumps: https://www.lead2passexam.com/NetworkAppliance/valid-NS0-521-exam-dumps.html
Verified & Latest NS0-521 Dump Q&As with Correct Answers: https://drive.google.com/open?id=1s4_DWgsLhuiJXxpaRre5_WIPa67qZ40O