[Oct-2021] NS0-176 Pre-Exam Practice Tests | Exam Questions and Answers for Cisco and NetApp FlexPod Study Guide
Cisco and NetApp FlexPod Implementation and Administration Certification Sample Questions
NEW QUESTION 77
How should the speed be configured on the Nexus 5548 port connecting to the Nexus 1100-X?
- A. Speed 1000
- B. It should not be configured - the 5548 will auto detect the correct speed
- C. Speed 10
- D. Speed 1G
- E. Speed 1000000
Answer: A
NEW QUESTION 78
Which sends support summary information to NetApp through HTTPS?
- A. TechSupport
- B. AutoSupport
- C. FlexSupport
- D. SnapSupport
Answer: B
NEW QUESTION 79
Exhibit:
Which hardware component is shown in the exhibit?
- A. GEM
- B. Fl
- C. VIC
- D. IOM
Answer: D
NEW QUESTION 80
Your primary VSM needs to be edited, rebooted, or migrated. You need to initiate a manual switchover to your standby VSM.
What command will allow this to occur?
- A. vsm switchover
- B. Standby activate
- C. System switchover
- D. System standby
Answer: C
NEW QUESTION 81
Which two are required for single-wire management for Cisco UCS C-Series? (Choose two)
- A. 10 GB LOM
- B. FI 6200 family only
- C. VIC 1240
- D. Redundant Nexus 2232PP FEX
- E. VIC 1225
- F. UCS Manager 2.1 or higher
Answer: E,F
NEW QUESTION 82
Which two features allow multiple fabric logins through a single port? (Choose two.)
- A. LLDP
- B. NPIV
- C. NPV
- D. vPC
Answer: B,C
NEW QUESTION 83
Which aggregates should be disabled for data aggregates?
- A. iSCSI
- B. FCP
- C. Snapshot copies
- D. SnapMirror copies
Answer: C
NEW QUESTION 84
Your customer needs a new Nexus switch that can support at least ten 40GbE ports, and has room for future growth. Your customer would also like the new switch to be Application Centric Infrastructure- ready.
Which switch meets these requirements?
- A. Nexus 5672
- B. Nexus 9504
- C. Nexus 7004
- D. Nexus 6004
Answer: B
NEW QUESTION 85
Exhibit:
You are configuring iSCSI boot from SAN on your UCS blades.
Referring to the exhibit, how many paths will there be to the Boot LUN?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 86
Which set of commands maps VLAN 100 to VSAN 100?
- A. Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100
- B. Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100
- C. Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100
- D. Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100
Answer: C
NEW QUESTION 87
Exhibit:
You have a NetApp cluster and have just performed a storage failover giveback command from the CLI.
Referring to the exhibit, what is the status of the storage failover process?
- A. The giveback is partially completed waiting for node cluster-01 to give back the partner's SFO aggregate.
- B. The giveback failed because cluster-01 was not able to communicate with the partner's cluster LIFs.
- C. The giveback is partially completed waiting for node cluster-02 to give back the partner's SFO aggregate.
- D. The giveback failed because the partner node was not in a "waiting for "giveback" state.
Answer: C
NEW QUESTION 88
Which is a valid connectivity option for a FlexPod?
Note some of these may also be 'valid' options outside of a FlexPod architecture but do not specifically meet FlexPod scalability and availability requirements.
- A. UCS C-Series direct attach FAS
- B. UCS B-Series > 2232PP FEX > UCS FI > Nexus 5548 < FAS
- C. UCS C-Series > 2232PP FEX > UCS FI > Nexus 5548 < FAS
- D. UCS B-Series direct attach FAS
- E. UCS C-Series > Nexus 3048 < FAS
- F. UCS B-series > UCS FI > 2232PP FEX > Nexus 5548 < FAS
- G. UCS B-Series > UCS FI > Catalyst 3750 < FAS
Answer: C,E
NEW QUESTION 89
You are asked to create an interface group on a NetApp clustered Data ONTAP system. The system is connected to a Cisco Nexus switch in a vPC configuration with the port-channel mode set to active.
Which NetApp interface group made matches this switch configuration?
- A. multimode
- B. singlemode
- C. mode active
- D. multimode_lacp
Answer: B
NEW QUESTION 90
Click the Exhibit button.
On your NetApp storage system, you create a volume named datastore1, mount it to a junction path, and then set the correct export policy. When you attempt to mount the volume from VMware ESXi as a datastore, the server is unable to mount the path /datastore1. You verify that your existing NFS datastore (/datastore0) on the same NetApp storage system SVMis functioning normally.
Referring to the exhibit, what is preventing the server from mounting the new datastore?
- A. The volume is too large to be mounted as an NFS datastore
- B. The LIF needs to be at its home-port when the volume is mounted.
- C. The load-sharing mirrors need to be updated.
- D. Two volumes cannot be mounted using the same LIF IP address.
Answer: C
NEW QUESTION 91
You are an administrator of a UCS system. You notice that when you apply a setting that requires a reboot, the affected hardware reboots immediately without warning. You would like to reboot to be acknowledged by an administrator instead.
What should you do to accomplish this task?
- A. Create aa BIOS policy.
- B. Create a scrub policy.
- C. Create a maintenance policy.
- D. Create updating templates.
Answer: C
NEW QUESTION 92
Which two are characteristics of a Fibre Channel SAN data LIF? (Choose two.)
- A. It can be associated with an IP address.
- B. It can be associated with an Ethernet port or VLAN interface.
- C. It can be associated with an interface group (ifgrp).
- D. It is associated with the management LIF.
- E. It can be associated with a WWPN.
- F. It can be associated with a Fibre Channel port.
- G. It is associated with the administrative Vserver.
Answer: E,F
NEW QUESTION 93
You are deploying a new virtual machine (VM). Your customer requires that the VM cannot reserve space on the VMFS filesystem, and the VM can only consume blocks when data is written to disk from and within the VM/Guest OS.
Which virtual disk should you create to meet these requirements?
- A. Thin Provision
- B. Independent Nonpersistent
- C. Thick Provision Eager Zeroed
- D. Thick Provision Lazy Zeroed
Answer: A
NEW QUESTION 94
The storage administrator created an export policy for a volume on a NetApp cluster.
The export policy contains a single export rule with the parameters shown below.
- protocol nfs - rorule any
- clientmatch 10.1.16.0/255.255.255.0 - rwrule any
Two hosts attempt to access the volume using the NFS protocol shown below.
- HostA with IP address 10.1.17.37 sends an access request using the NFSv3 protocol
- HostB with IP address 10.1.16.24 sends an access request using the NFSv4 protocol
Which statement about this scenario is true?
- A. HostA will be granted RO/RW access to the volume; HostB's access to the volume will be blocked by the protocol parameter.
- B. HostA's access to the volume will be blocked by the clientmatch parameter; HostB will be granted RO/RW access to the volume.
- C. HostA's access to the volume will be blocked by the protocol parameter; HostB will be granted RO/RW access to the volume.
- D. HostA's access to the volume will be blocked by the clientmatch parameter; HostB's access to the volume will be blocked by the protocol parameter.
Answer: D
NEW QUESTION 95
Exhibit:
Your customer has a FlexPod VMware solution deployed with NFS datastores. As shown in the exhibit, the links between the Fabric Interconnects and storage controllers are single-mode interface groups with autorevert set to true, hosting a single access LIF. NFS I/O is currently going through fabric A to ST-A. The customer wants to use both fabrics for NFS I/O.
In this scenario, what will accomplish this task?
- A. Configure VMware hosts to utilize an NFS LIF on ST-B that is connected to fabric A.
- B. Configure VMware hosts to use a new datastore with an NFS LIF on ST-B connected to fabric B.
- C. Add two physical links between SW-A and SW-B.
- D. Migrate the existing LIF that is used for NFS I/O on ST-A to its HA partner ST-B.
Answer: B
NEW QUESTION 96
Under which tab in UCS Manager would you create a boot policy?
- A. SAN
- B. Servers
- C. Equipment
- D. LAN
Answer: B
NEW QUESTION 97
When configuring a volume to contain a LUN, which administrative tool automatically applies NetApp recommendations?
- A. Microsoft SystemCenter
- B. Data ONTAP command-line interface
- C. VMware vSphere
- D. OnCommand System Manager
Answer: D
NEW QUESTION 98
......
Network Appliance Exam Practice Test To Gain Brilliante Result: https://www.lead2passexam.com/NetworkAppliance/valid-NS0-176-exam-dumps.html