Use Real 300-615 Dumps - Cisco Correct Answers updated on 2021
CCNP Data Center 300-615 Exam Practice Dumps
NEW QUESTION 23 
Refer to the exhibit. The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?
- A. Reconfigure the initiator and the target to be in the same zones.
- B. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
- C. Reactivate the zoneset.
- D. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.
Answer: C
Explanation:
Section: Storage Network
NEW QUESTION 24
During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection. Which set of steps resolves the issue?
- A. 1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord - B. 1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server - C. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server - D. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/ts/guide/b_C-Series_Troubleshooting_Guide.pdf
NEW QUESTION 25
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION 26
Refer to an exhibit.
An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?
- A. Load a new system image.
- B. Use the same system image as the kickstart image.
- C. Reload the same system image.
- D. Save the system image in NVRAM.
Answer: A
NEW QUESTION 27
Refer to the exhibit.
vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
- A. Configure IP address on the interface.
- B. Configure one of the switches as primary for the vPC.
- C. Activate VLANs on the vPC.
- D. Configure vPC peer link and vPC peer keepalive correctly.
- E. Match vPC domain ID between the two devices.
Answer: C,E
NEW QUESTION 28
An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN.
The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot. Which action resolves the issue?
- A. Remove all of the local storage that is installed
- B. Remove all of the ISO images that are mounted as a virtual CD-ROM
- C. Delete and reconfigure the boot LUN
- D. Delete and reconfigure the pWWN of the SAN boot target
Answer: A
NEW QUESTION 29
Refer to the exhibit.
After the configuration is performed, guestshell continues to use 2%CPU. Which action resolves the issue?
- A. Resync the database
- B. Reboot the switch
- C. Reboot the guestshell
- D. Recreate the guestshell
Answer: C
NEW QUESTION 30
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION 31
The external routes fail to propagate to leaf switches in Cisco ACI fabric Which two actions resolve the issue?
(Choose two.)
- A. Specify the spine nodes as route reflectors
- B. Enable the VTEP pool in the fabric
- C. Associate the correct contract to the L30ut.
- D. Configure an MP-BGP area.
- E. Assign an MP-BGP AS number to the fabric.
Answer: A,E
NEW QUESTION 32
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?
- A. Decomission the server.
- B. Re-acknowlegement the server.
- C. Perform diagnostic interrupt on the server.
- D. Reset the server.
Answer: B
Explanation:
Section: Compute Platforms
NEW QUESTION 33
The external routes fail to propagate to leaf switches in Cisco ACI fabric. Which two actions resolve the issue?
(Choose two.)
- A. Enable the VTEP pool in the fabric.
- B. Specify the spine nodes as route reflectors.
- C. Configure an MP-BGP area.
- D. Assign an MP-BGP AS number to the fabric.
- E. Associate the correct contract to the L3Out.
Answer: B,D
Explanation:
Section: Network
NEW QUESTION 34
A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?
- A. Remove all existing vNICs and add them in the desired order.
- B. Build a new service profile with the desired network configuration
- C. Create a vNIC placement policy to avoid adapter renumbering
- D. Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs
Answer: C
NEW QUESTION 35
After upgrading a client's fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)
- A. Service profiles page, InternalBackup stage
- B. Equipment FSM page, InternalBackup stage
- C. Admin page, InternalBackup stage.
- D. Admin page, PollInternalBackup stage
- E. Equipment FSM page, PollInternalBackup stage
Answer: B,D
Explanation:
Section: Management and Operations
NEW QUESTION 36
Refer to the exhibit.
An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?
- A. The interface is working correctly and fully operational, but it is not in use.
- B. "out-of-service" indicates that no service graph is in use for this interface.
- C. "out-of-service" is the default interface status in ACI.
- D. The interface policy is misconfigured.
Answer: D
NEW QUESTION 37
Refer to the exhibit.
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- A. VSAN 1 is suspended.
- B. Trunk mode must be activated.
- C. The SFP is unsupported.
- D. The interface is in an incorrect mode.
Answer: B
NEW QUESTION 38
Refer to the exhibit.
An upgrade operation fails with an error displayed. Which action resolve the issue?
- A. Use a different system image
- B. Allocate extra space on a flash drive to extract a system image
- C. Allocate extra space on a flash drive to extract a kickstart image
- D. Use a different kickstart image
Answer: A
Explanation:
Kickstart image verification succeeded. System image has failed.
NEW QUESTION 39
Refer to the exhibit.
Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?
- A. Acknowledge the primary fabric interconnect.
- B. Remove the service pack from the subordinate fabric interconnect.
- C. Clear the startup version of the default infrastructure pack.
- D. Upgrade the firmware of the infrastructure firmware by using the force option.
Answer: C
NEW QUESTION 40
......
Get ready to pass the 300-615 Exam right now using our CCNP Data Center Exam Package: https://www.lead2passexam.com/Cisco/valid-300-615-exam-dumps.html
300-615 Premium Files Test pdf - Free Dumps Collection: https://drive.google.com/open?id=1N1XTxyyMtZYOkgaC7iknNabqAMtHnwJN