Verified NS0-184 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump from Lead2PassExam
Pass NCSIE ONTAP NS0-184 Exam With 60 Questions
There are the resources that you can use to get for the Network Appliance NS0-184 Certification Exam
These resources are available online, and they are extremely useful for the preparation of the Network Appliance NS0-184 Certification Exam. The Network Appliance NS0-184 Certification Exam prep can be made easy by using the Network Appliance NS0-184 Certification Exam prep materials. The NS0-184 Exam preparation materials can be downloaded from the official website of the Network Appliance NS0-184 Certification Exam. The practice materials are quite useful for the practice of the NS0-184 Exam. You should select the Network Appliance NS0-184 Exam prep stuff that is easy to understand and is useful for the preparation of the Network Appliance NS0-184 Certification Exam. The Network Appliance NS0-184 Certification Exam practice stuff should be up-to-date, and it should contain the relevant information that is needed for the practice of the Network Appliance NS0-184 Certification Exam.
For getting the most relevant data, you can go through the books, the study guides, and the sample questions & answers that are available online. You can also watch YouTube videos, take online tutorials, enroll in a course related to the real Network Appliance NS0-184 Certification Exam. But you are recommended to take the PDF NS0-184 Dumps of the Lead2PassExam. It is the blend of all the resources that can help you to get ready for the Network Appliance NS0-184 Certification Exam. Its Web simulators and mobile application are also available for the convenience of the candidates. The practice exams of the Lead2PassExam are updated on a regular basis, and they are useful for the preparation of the Network Appliance NS0-184 Certification Exam.
NEW QUESTION # 11
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have IPv6 configuration set.
- B. You do not have a static IP address.
- C. You do not have network discovery enabled.
- D. You do not have a default gateway set.
Answer: D
NEW QUESTION # 12
On which type of network interfaces are the cluster interconnect LIFs created?
- A. on a physical port
- B. on a UTA port shared with other LIFs
- C. on an interface group
- D. on an FC or FCoE port
Answer: C
NEW QUESTION # 13
You are preparing to physically install a new AFF A400 cluster into a customer's racks. All equipment has been delivered to the customer's site.
Which three tools do you need to complete this installation? (Choose three.)
- A. Phillips #2 screwdriver
- B. additional network cables
- C. slide rail kit
- D. laptop computer
- E. cable management tray
Answer: A,B,D
NEW QUESTION # 14
Which logical interface has a fixed firewall policy?
- A. cluster LIF
- B. data LIF
- C. intercluster LIF
- D. cluster management LIF
Answer: A
NEW QUESTION # 15
You are installing a 4-node AFF A400 cluster and are asked to create a custom security message before and after user login.
Which two security features are used to perform this task? (Choose two.)
- A. AutoSupport
- B. banner
- C. EMS
- D. motd
Answer: A,B
NEW QUESTION # 16
Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.
In this scenario, which two prerequisites should you examine in advance? (Choose two.)
- A. Verify that the platform of the new controllers can be mixed with the cluster's existing controllers.
- B. Verify that the hard drives of the new controllers are compatible with the old controllers.
- C. Verify that the existing cluster has a minimum 10 GB of free space for root volumes.
- D. Verify that the existing switches support the additional controllers.
Answer: A,C
NEW QUESTION # 17
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)
- A. shelf connectivity
- B. node CPU utilization
- C. cluster switch cabling
- D. data switch cabling
Answer: A,B
NEW QUESTION # 18
Your customer wants to know more about the network configuration within the cluster.
In this scenario, which statement is correct about a LIF?
- A. A LIF is a port that provides physical connections.
- B. A LIF separates network domains to access cluster data.
- C. A LIF is an IP address or a WWPN that is associated with a port.
- D. A LIF is created within a broadcast domain and contains a pool of IP address.
Answer: C
NEW QUESTION # 19
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)
- A. Hardware Universe
- B. Active IQ Config Advisor
- C. Interoperability Matrix Tool
- D. Active IQ System Manager
Answer: B,C
NEW QUESTION # 20
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. You can change any drives or disk shelves as part of this replacement procedure.
- B. You must move the boot device from the impaired node to the replacement node.
- C. The boot device must remain intact and must not be removed from the impaired node.
- D. A controller model of the same type must be used to replace the impaired node.
Answer: B,D
NEW QUESTION # 21
You have an AFF All SAN Array (ASA) cluster that is running ONTAP 9.7. The cluster is configured for Active Directory domain controller access using a domain tunnel.
In this scenario, which two licenses are enabled on the cluster? (Choose two.)
- A. NVMe
- B. CIFS
- C. FCP
- D. iSCSI
Answer: B,C
NEW QUESTION # 22
Click the Exhibit button.
As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.
In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)
- A. private network
- B. management LIFs
- C. client network
- D. cluster LIFs
Answer: A,D
NEW QUESTION # 23
You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.
Which two additional steps must be taken to bring the additional ports online? (Choose two.)
- A. Reload the RCF file
- B. Re-enable each port
- C. Reload the firmware
- D. Reload the switch
Answer: A,D
NEW QUESTION # 24
Click the Exhibit button.
During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.
Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)
- A. Contracts and Warranties
- B. ASE Corner
- C. Active IQ
- D. Guide Me
Answer: A,D
NEW QUESTION # 25
An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.
In this scenario, which tool would the administrator use to validate the configuration?
- A. NetAppDocs
- B. Active IQ Upgrade Advisor
- C. Interoperability Matrix Tool
- D. Active IQ Config Advisor
Answer: A
NEW QUESTION # 26
You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither "un-failing" nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.
In this scenario, which two actions should you take? (Choose two.)
- A. Power off the system until the drive has been replaced.
- B. Ask the customer to open a technical case with NetApp Support.
- C. Ask the customer for a drive with the same capacity and replace it.
- D. Run Active IQ Config Advisor to collect all the logs on the system.
Answer: C,D
NEW QUESTION # 27
......
NetApp NS0-184 Exam Topics:
| Section | Objectives |
|---|---|
| ONTAP Networking | - Describe how to configure ONTAP system networking - Describe network types used with ONTAP clusters |
| ONTAP Switches | - Describe cabling of a switched cluster - Identify the software needed for cluster switch configuration |
| ONTAP Concepts | - Identify how to update ONTAP - Identify ONTAP cluster controller components - Describe how to create aggregates - Describe the required steps for installation or expansion of an ONTAP cluster |
| Customer Handoff | - Describe the tools available to review an installation - Describe the process for handover of new ONTAP cluster installation to the customer - Identify how to create documentation |
| Basic Installation Topics and Tools | - Describe the required tools or documentation for preparing the installation of a new ONTAP cluster -Describe physical cabling of ONTAP nodes |
Ultimate Guide to Prepare Free NS0-184 Exam Questions and Answer: https://drive.google.com/open?id=1qh_EKlrWKJ7WGSOOyDr9am9xFWwl24bw
Pass NS0-184 Tests Engine pdf - All Free Dumps: https://www.lead2passexam.com/NetworkAppliance/valid-NS0-184-exam-dumps.html